Replacing uPVC Window Handles

It is easy to change the handles on windows made of Upvc. The important thing is to ensure that the replacement handle fits the spindle that was cut out of the window mechanism.

If you follow the steps below the handle of any cockspur will fit most windows. The most important factor is the step size of the handle.

What to Look For

A lot of windows in the UK come with uPVC handles Over time, they may begin to show signs of wear and tear. The handle of the window can become loose or difficult-to-operate when this occurs. This is a fairly simple task that is achievable by anyone who is comfortable using basic hand tools.

The first step is to make sure that the handle is securely attached to the frame of the window in the open position. The next step is to locate the fixing pins or screws that hold the handle in place. They are usually located on the inside face of the handle and are removed with a screwdriver or pliers.

When the handle has become loose, gently pull it away from its hinges. Then, you'll have to find a new handle that is the same size and style. This can be accomplished online or at the local DIY store and it should take about five minutes with a screwdriver.

The most important thing to consider when replacing a uPVC window handle is the step height. This is the distance between the handle's base and the place it is located within the frame of the window. This is a typical measurement, and you should verify the step height before ordering an replacement handle.

There are a variety of sizes based on the type of handle. Inline handles for uPVC windows typically have lug centres of 31mm, and there are also handles with cockspur with 43mm centres. Tilt and turn handles are commonly found on windows made of uPVC and they feature a specific design that allows windows to be tilted in to allow for ventilation, and then turned to open the window fully.

The most frequent uPVC handle cracks are internal, rather than a fracture from the base. This can make them hard to open, and it is therefore essential to ensure that the replacement handle you buy has the same spindle length as the one you have.

Remove the handle that was previously used

A poorly installed or damaged window handles could cause your double glazed windows to open or close improperly and could even result in them getting stuck. This could be due to various reasons, including general wear and tear on the handle or corrosion. In these instances, it is important to locate replacement window handles made of upvc as soon as you can to prevent further damage and loss of functionality.

When replacing the handles on windows made of upvc, you should remove the handles that were previously installed from the window. Begin by removing the screw when the handle in closed position. Once you have removed the screw, you can take off the handle. It is a good idea to employ an electric screwdriver to accomplish this as it will make the task much easier and quicker.

It is also worth noting that the handles' screws could be hidden behind caps made of plastic, so it is a good idea to use an Stanley knife to the screw caps and then take them off. Once the old aluminium window handles handle is removed, you must take a look at the square cut out at the base of the handle to make sure that the new window lock handles will work with it. It is essential to measure the spindle length on the handle that was used and compare it to the size of the window mechanism spindle cutout.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right, Cranked handles with two screws and Spade handles, which have flat arms and can be used either side of the windows made of upvc. Once you have found a suitable replacement, it is simply a case of screwing the handle in place and making sure that the spindle is correctly inserted into the lock mechanism. After that, you can then tighten the handle to the window frame. The replacement handles for upvc windows upvc handle will now be secure.

Measure the Spindle

If you're replacing a upvc window handle that has fallen off, it is likely because the spindle that holds it in place has become loose or damaged. In some cases this can be fixed by using screws or pins to tighten it. In other cases it will require replacement completely. There are many kinds of window handles made from upvc. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is mounted and replaced in a different fashion.

Before purchasing a replacement handle it is important to know the size of the handle that is currently in use. This will ensure that the new handle is of the correct size and will fit correctly within the window. All handles are calibrated in accordance with industry standards, making it easy to identify the correct size.

To measure the size of the handle move the window to the open position. You should then be able to determine the size of the screw or pin that is holding it. Use a ruler or a tape measure to determine the length the spindle is. Once you know the length of the spindle you can purchase a new one that is exactly the same size.

The step height of a window handle is also a factor to take into consideration when purchasing an alternative. The step height is measured from the base to the point at which the handle sits on the frame. It is typically around 21mm or 9mm in aluminium and uPVC. Dropping objects into the space will allow you to determine how far the handle extends before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights, based on the type of window they're installed in. Inline Espag handle heights are 43mm from centre to centre (two fixing points). Cockspur handles for bifold doors however have different backset heights dependent on the design of the window they're in. This is because they feature spurs that extend from the handle and locks over a cockspur wedge striker plate.

Install the new handle

After you have chosen the new handle, make sure it is aligned with the holes for screws on the door. Then, secure it with the screws provided. If you're replacing the latch lever it can be put in the same way as the door handle. After that, attach the bifold door handles trim to hide the mounting screws and close off your project.

Tips: To remove the metal head from a wooden wedge, place the handle on the floor so that its wide end is level with the ground. Then, you can use to tap the thin end. Be careful not to scratch the handle or handle spindle.