Reasons Your Fiat Punto remote key price 500 Key Fob Won't Work

A key fob from fiat 124 spider key fob not working 500 is a great way to open the doors and start the car. There are a variety of reasons why the key fob might stop working. These include a dead battery water damage, receiver module issues, or interference.

This listing is for a NEW replacement key fiat 500 fiat panda key fob replacement Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths in the automotive industry). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't work is a dead battery. Modern key fobs operate with a limited operating range, and should be within only a few feet from the vehicle in order to function. If you are far from your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the battery of your coin cell (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store, or online.

You can test the battery in the coin-cell by pressing the buttons while standing close to your fiat ducato key replacement 500. The car will blink its parking lights, and the key fob should operate the lock and unlock switches.

If the fob's key doesn't function after replacing the battery, it could be damaged by water that blocks it from connecting to the receiver module inside your vehicle. Water damage can occur in a variety of ways, from an accidental splash to submerging your fob in salt water at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If that doesn't work, your fob may require reprogramming by an experienced auto locksmith or the dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean, or wash it in a washer. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually end up dying. Getting the fob wet is not an ideal choice but if you accidentally drop it into an empty cup of water, or forget to remove it from your pants pocket prior to running the washer and you don't have a chance, don't give in.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Test the fob next to check if it's working. If the fob doesn't work, it might need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is more recent and hasn't been programmed to your car, it will likely need to be replaced completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition in your vehicle. The locksmith will also need to program your fob into the vehicle's system. This is a low-cost and fast process that can be completed in the same day.

Receiver Module Issues

Your 500 fiat 500x key fob programming fob may stop working because it is out of range. The remote usually has 30 feet of range or less, and if it's too far away from your car it will not respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If your fob isn't working after you replace the battery inside the coin, which is also known as a "button", "watch" or "button", it could be a problem with the circuit board inside. Reprogramming the fob is usually the solution to this issue. You can find instructions on how to do this for the majority of vehicles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal clips that hold the battery of your coin in place. If they lose tension, they could stop the battery from being seated properly, and this will cause your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, the software may also need to be reinstalled in your body control modules.

Interference

In addition to a dead coin battery the key fob could not be receiving or transmitting the signal due to interference. This may happen if the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons why the key fob might not function include a weak connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a malfunctioning receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computers, which could allow you to the key fob to function again. If the issue persists you should speak with an expert technician. They can identify the exact cause of any issues.