Reasons Your fiat 124 spider key fob cover 500 fiat ducato key fob programming Fob Won't Work

A key fob from fiat 500 remote key programming 500 makes it easy to open doors and start your car. There are a myriad of reasons the fob could stop working. It could be due to a dead battery, damage to the receiver module, water problems, and interference.

This listing is for a NEW replacement fiat 500 electric key Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't work is the battery is dead. Modern key fobs operate with a limited operating range and must be within just a few feet of the vehicle in order to function. If you are far from your car and press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. They are available at your local hardware store, or online.

After you've changed the battery on the coin cell, you can test it by standing close to your fiat van keys 500 and pressing the buttons. The parking lights will flash and the key fob should operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module in your vehicle. Water damage can happen in a number of ways, from an accidental splash to submerging the fob into salt water at the beach. If you believe your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work, the fob might need to be reprogrammed by a professional locksmith or dealer.

Water Damage

The fob does have rubber seals that keep water out of the electronic chip inside and out of the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the fob's circuit board, causing it to short out and eventually die. If you get the fob wet, it's not a good idea, but if you drop it into a cup of water or don't remember to take it out of your pants pocket before running the washer Don't give up hope.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Check the fob again to check if it's working. If the key does not function it could need to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is a bit older and not programmed for your vehicle You will need to replace it completely. A professional locksmith in the automotive industry can complete this simple process. The locksmith will need to cut the key to match the ignition of your car. The locksmith also needs to program your fob into the car's system. This is a quick and affordable process that is usually completed the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob may stop working is because it's out of range. The remote usually has an operating range of 30 feet or less and if it's far from your car, it will not respond to your commands. You can easily fix this by moving the remote closer to your vehicle until it responds.

If your fob does not work after replacing the battery for the coin, also known as a "button", "watch" or "button" or "button", it could be a problem with the internal circuit board. In the majority of cases, reprogramming your fob will solve the issue. You can find directions on how to do this for most automobiles by searching YouTube or consulting the owner's manual.

You may have to replace the metal retaining clips that hold the coin battery in place. If they become loose, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob could be out of sync with your vehicle because of software or hardware problems. This can cause a major problem, but you can usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain situations they might need to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could happen if the key fob is near the radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob could not function due to a bad connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, detects radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

There is a simple way to reset the 500's internal system including the keyfob. Disconnect the 12 volt battery for about 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electricity and then restart the car's computers. This could allow you to the key fob to function again. If the issue persists you should speak with a certified technician. They can identify the root cause of your issue.