How to Replace a Saab 9-3 Key

The Saab 9-3 is a car that has a large deal of appeal for drivers. It has a powerful engine as well as excellent visibility. It has a very high safety rating.

However, it's important to ensure that you have at minimum two keys that work for your car. If you lose the only key, it can be very expensive to add an additional one.

How to Replace the Ignition Key in a Saab9-3

If your car key won't turn on it is time to replace it. This guide will guide you through how to do it on a Saab 9-3. You'll have to replace the key, purchase another reprogrammable device, and then purchase a new casing for your key-fob.

The majority of modern Saab models make use of a transponder instead of a metal key to unlock the car and begin it. The issue with this is that the reprogrammable battery in the key-fob will eventually wear out and won't hold a charge any longer. This is particularly relevant if you continue to use the same key with the same lock.

The good part is that the battery can be replaced easily by a professional locksmith. You can also do it yourself if you have the necessary tools and a little bit of patience. The first step is to take the key-fob out. This is done by inserting a flathead screwdriver in the slot in the middle of the case. The plastic is very thin and easily damaged.

Once the case is opened, you can make the new key by combining lower part of old key with a transponder and banana. This will ensure that the new key is connected to the CIM properly, which can make a big difference when replacing the primary key for your Saab 9-3.

How do I replace the ignition Key in a saab key replacement 900

If you do not have two keys, you'll have to take off the steering wheel and dashboard in order to access the ignition. Start by disconnecting the negative battery cable. After the battery has been disconnected, it is possible to remove the trim and dashboard pieces that surround the steering wheel. Once the dash is removed, you can put a screwdriver in the opening behind the ignition switch.

The ignition barrel is equipped with a key lock that could stop the vehicle from starting if you don't have a key. If the ignition switch of your 900 isn't working properly, check the key to determine whether it's inside the lock or is stuck in the barrel of ignition. It is also important to rotate your keys and keep them clean to avoid bending.

Saab cars differ from other cars because they do not use traditional keys made of metal. The car instead recognizes the electronic signals coming from the key fob via the use of a special microchip.

If you have lost your only working key fob, the dealer will charge the highest dollar to replace your computer module (known as the CIM). We can reprogram the EEPROM of your current computer to enable it to accept new keys without having to replace it. This will save you over 50% of what the dealer charges! We call it the SAAB KEY PROGRAM. Find out more about it here!

How to replace the ignition Key on a Saab 9-5

The metal part of a traditional Saab key is easy to copy, and is also not much of a barrier against vehicle theft. The real security is the electronic component of the key-fob, which has a chip inside which recognizes your car once it's inserted into the ignition switch.

Saab's anti-theft device has been relying on this technology for over 10 years. It's not quite as effective as a physical lock for your door, near but it makes stealing your car a lot more difficult. Every Saab owner must keep an extra saab ignition key replacement key in their car.

The majority of new Saabs are delivered with two keys, however they are also available for purchase at an dealer by using a handheld device known as Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 models, that have more modern, newer features that require the use of a key-fob.

The dealer will replace the CIM or TWICE module in these cars if the keys are lost. They'll charge you a high price to do it. We can however reprogram the EEPROM in your existing computer to accept new keys without replacing the expensive modules.

How to Replace the Ignition Key on an XC90 Saab

If your SAAB 9-3 key fob starts having problems turning the lock barrel it could be time to replace it. The process is quite simple and doesn't require you to visit an agent. Instead you can complete the process yourself at home, using just some basic tools.

First, you'll need to prepare the new key. Before you begin, turn off the anti-theft system by placing blocks under your rear wheels and releasing your handbrake. Then, put the key in the ignition and move it to the on position which activates the accessories, but it doesn't start the engine. Repeat this procedure 5 times, and then keep the key on the "on" position.

You'll need to purchase a new case for your key fob. They are readily available at many auto parts stores and are usually extremely affordable. Depending on the model, you may even purchase them without electronic components.

To open the case to open the case, gently push the flathead screwdriver into the slot in the middle. The case should break easily and, once you do, you'll have access to the internal electronics. To get rid of the electronics, make use of a small screwdriver and try to pry them out with a gentle force.